昊星JQB型柱塞式氣動漿料泵系列
一、產品概況:
昊星JQB型柱塞式氣動漿料泵系列(簡稱：氣動漿料泵、氣動泵、漿料泵，又名：氣動泵插桶泵、氣動防爆插桶泵柱塞式、油桶泵、氣動活塞泵、氣動柱塞泵、氣動濃漿泵、氣動往復泵、氣動打膠泵、氣動抽液泵，氣動防爆不鏽鋼泵，皮革噴漿泵、高粘度漿料泵、氣動泵浦、打漿料泵浦)廣氾應用於人造革、移膜革、壓延革、彩塗板、印染、醫藥、塗層、化工、紡織、噴漆、噴塗、薄膜鍍鋁、彩鋼瓦、油墨、日化、環衛、礦產、塑料助劑、中間體、PU發泡、PVC、有機溶劑等領域行業的低、中、高黏度液料輸送。適用於介質高粘度(VIS)≤12萬CPS/25℃的化工漿料及其它原液料，本泵具有防爆、防沉澱、耐腐、耐用、低噪音、節能、體積少、重量輕、易操作、穩定性好等功能，是一種很理想的移動輸送設備。
JQB型氣動漿料泵產品是引進國外 工藝研製而成的，工作原理是採用氣壓差的作用，使活塞上下運行，帶動導料活塞開閉，起到提料的作用。調整給氣動漿料泵工作氣體的流量與氣壓來控制和氣動泵調節送料流量。結合感應開關能使之自動化流程工作。
二、結構說明：
|
|
昊星SINOSTARS氣動漿料泵(柱塞式)JQB系列 結構．圖一 |
三、使用方法：
1、首先，應保証氣動管路（壓縮空氣氣源管道）連接符合要求，大氣壓能夠穩定達到0.5～1.5MPa範圍，並將氣動管路牢固地連接在氣動漿料泵進氣咀上，這時將油杯注入潤滑油后擰緊，把氣動漿料泵導料管（吸料口）正確放入所要輸送的料桶（料池或其它容器）內。
2、將耐腐蝕軟管連接出料口接至送料地點。
3、氣動漿料泵進氣閥呈關閉狀態，然後將氣源管連接進氣閥接頭。開始操作時請扳動控制氣閥，要開啟和關閉反復測試至無異常，根據所需漿料流量來開啟進氣閥，調節氣動漿料泵運行頻率，即可工作運轉。
四、注意事項：
1、昊星氣動漿料泵工作時，泵的進氣咀前端氣動管路上必須安裝空氣過濾器、油霧器使其處在 工作狀態。
2、昊星氣動漿料泵在使用時，發生油杯處滲漏漿料應把油杯擰緊， 如擰到底后還有洩漏現象可將油杯拆下，加上密封墊片兩塊重裝。
3、昊星氣動漿料泵在清洗時，首先將吸料裝置拆下，再把氣缸和吸料管分解開，將提動柱塞（活塞）從吸料管下部抽出進行清洗.........
五、維護保養：
1、昊星氣動漿料泵在使用過程中防止撞擊缸體部位避免變形，發生氣動柱塞（活塞）卡死現象，造成故障或以致嚴重報廢。
2、昊星氣動漿料泵氣動柱塞（活塞）在運行1000000余次后，根據空壓機送氣過程中水份積留情況應清缸體，塗注30#優質潤滑油。
3、昊星JQB型氣動漿料泵如經久不用，應在溶劑內工作狀清洗，防止漿料凍結，阻塞導料管而產生故障。
六、使用範圍:
昊星JQB型氣動漿料泵可輸送酸、碱、鹽、油品、飲料、塑料助劑、聚酯、聚合物等介質，特別是適用於化工、石油化工、精細化工、染料化工、環保、水處理、醫藥、食品等行業。
昊星JQB型氣動漿料泵，又名氣動插桶泵(油桶泵、、皮革漿料泵、打料漿料泵)代替進口漿料泵專為人造制革濕法和干法生產制備必不可缺少的輸送設備及其他工業行業塗台漿料輸送而設計，具有防爆、耐腐、耐用、防沉澱、節能、低噪音、體積少、重量輕、易操作、穩定性好、移動輸送設等特點。
七、昊星JQB型氣動漿料泵（柱塞式）性能參數:
|
主要性能 |
A0.8 |
B1.2 |
C2.8 |
D3.0 |
D3.2 |
|
工作環境溫度℃ |
-40～40 |
||||
|
使用氣壓MPa |
0.5～1.5 |
||||
|
輸送流量T/h |
0.8 |
1.2 |
2.8 |
3 |
3.2 |
|
輸出壓力MPa |
0.2～2 |
||||
|
輸料黏度CP.S |
0～80000 |
||||
|
氣缸柱塞行程mm |
60 |
65 |
110 |
110 |
110 |
|
泵體總長度 |
1450 |
1450 |
1650 |
1660 |
1660 |
|
重量Kg |
13 |
15 |
18 |
20 |
26 |
|
注：昊星JQB型氣動漿料泵非常適用於低、中、高黏度介質，干、濕法仿皮合成革生產線上的漿料的自動輸送，和其他油料等介質的輸送。◆定做各種型式進出接口及泵連接管尺寸 |
|||||
產品優點︰
Titanium High-Speed Grinding Machine (New Colloid Mills) Hao Sar is committed to the development of large high-speed grinding machine colloidal mill Colloid Mill made great scientific and technological fruits, such as the patented new products: Multi-purpose grinding machine using a special dynamic seal (using a number of patented technologies), No material may be transferred under dry and will not damage dynamic seal and mechanical properties, maintenance rate is low, the friction power is small, grinding, dispersion fineness are "2-micron, the effect is good, and high efficiency. The machine spindle speed of up to 2000-3500 per minute forward, grinding line speeds of up to 1200-4500 meters per minute. Is mainly used for fineness demanding, difficult ground, scattered materials, completely replace the three-roll machine, imported grinding machine, heterogeneous machines and other equipment, our factory to develop new products Titanium Grinder SSJM-W250Ac-2; SSJM-W320Ac -2; SSJM-W400Ac-2, and other special models is currently the only instead of imported grinding machine or sanding machines, used in high-grade titanium dioxide - Titanium Dioxide (active titanium dioxide) on the preparation process, the production efficiency is the above-mentioned similar products several times, can significantly lower production costs, but the grains were uniform, clean easily change color, no grinding impurities. Can be widely used in: chemical industry, food industry, daily chemical industry, pharmaceutical industry, titanium dioxide industry, ceramic industry, bio-engineering and other fields, spearheaded the introduction of Seven Star Dairy Equipment Factory manufactured titanium dioxide slurry of the wet ultrafine particles specific grinding Machines: Titanium grinding machine SSJM-W250Ac-2 colloidal series, are: Haopu Titanium, Titanium simexco, Panzhihua titanium sea, Dong Jia Group, Gimpo Group, Nanjing Titanium Dioxide and other Chinese manufacturers used by leading enterprises and get users.
Seven companies for road bitumen industry, has developed the world's most cutting-edge products, modified bitumen mixture dispersed closed continuous grinding machine, Colloid Mills series and complete sets of production equipment to improve the traditional equipment of space occupied by large, high energy consumption, low efficiency drawbacks, in order to low power consumption, small space, high-quality, highly efficient integrated solution to replace the asphalt road and bridge has been widely used in the production process. Especially in the EVA / SBA mixed decentralized aspect of the product to achieve at the highest 380 ℃ and 16Bar under conditions of continuous mixing polymer and asphalt, asphalt maximum feed capacity of 35 tons / hour, the corresponding EVA / SBS maximum feed capacity will be increased to 8 tons / hour, and, at the same time the completion of modified asphalt, high-speed shearing, in order to achieve high standards of uniformity and fineness.
