| 产品规格︰ | Titanium High-Speed Grinding Machine (New Colloid Mills) Hao Star is committed to the development of large high-speed grinding machine colloidal mill Colloid Mill made great scientific and technological fruits, such as the patented new products: Multi-purpose grinding machine using a special dynamic seal (using a number of patented technologies), No material may be transferred under dry and will not damage dynamic seal and mechanical properties, maintenance rate is low, the friction power is small, grinding, dispersion fineness are "2-micron, the effect is good, and high efficiency. The machine spindle speed of up to 2000-3500 per minute forward, grinding line speeds of up to 1200-4500 meters per minute. Is mainly used for fineness demanding, difficult ground, scattered materials, completely replace the three-roll machine, imported grinding machine, heterogeneous machines and other equipment, our factory to develop new products Titanium Grinder SSJM-W250Ac-2; SSJM-W320Ac -2; SSJM-W400Ac-2, and other special models is currently the only instead of imported grinding machine or sanding machines, used in high-grade titanium dioxide - Titanium Dioxide (active titanium dioxide) on the preparation process, the production efficiency is the above-mentioned similar products several times, can significantly lower production costs, but the grains were uniform, clean easily change color, no grinding impurities. Can be widely used in: chemical industry, food industry, daily chemical industry, pharmaceutical industry, titanium dioxide industry, ceramic industry, bio-engineering and other fields, spearheaded the introduction of Seven Star Dairy Equipment Factory manufactured titanium dioxide slurry of the wet ultrafine particles specific grinding Machines: Titanium grinding machine SSJM-W250Ac-2 colloidal series, are: Haopu Titanium, Titanium simexco, Panzhihua titanium sea, Dong Jia Group, Gimpo Group, Nanjing Titanium Dioxide and other Chinese manufacturers used by leading enterprises and get users.
Seven companies for road bitumen industry, has developed the world's most cutting-edge products, modified bitumen mixture dispersed closed continuous grinding machine, Colloid Mills series and complete sets of production equipment to improve the traditional equipment of space occupied by large, high energy consumption, low efficiency drawbacks, in order to low power consumption, small space, high-quality, highly efficient integrated solution to replace the asphalt road and bridge has been widely used in the production process. Especially in the EVA / SBA mixed decentralized aspect of the product to achieve at the highest 380 ℃ and 16Bar under conditions of continuous mixing polymer and asphalt, asphalt maximum feed capacity of 35 tons / hour, the corresponding EVA / SBS maximum feed capacity will be increased to 8 tons / hour, and, at the same time the completion of modified asphalt, high-speed shearing, in order to achieve high standards of uniformity and fineness.
|
| 产品优点︰ | 昊星GS型单螺杆泵的设计转速为输送清水或清水相类似的无腐蚀性液体时允许 转速，在实际使用中因介质性质与寿命要求不同，选用时一般都应低于设计转速，对高粘度和含颗粒介质，一般采用设计转速的 1/2-1/3 或更低些，低转速对泵的磨损有利，但在使用后由于定子的磨损流量下降，这时可适当提高转速，以补偿流量下降也为常策。输送介质的温度应在 -10 ℃～80℃特殊情况可高达120℃。
昊星GS型单螺杆泵的每级（定子的一个导程）正常压力为0.3~0.6Mpa，短时间（不超过30分钟）内允许高达0.6Mpa，当磨损后在相同输出压力时的容积效率要逐步下降。
昊星GS型单螺杆泵送清水时 吸程为 3米，实际使用建议不超过2.5米，当泵送高粘度介质时，应以正压吸入。
与其它类型泵相比：
和离心泵相比，单螺杆泵不需要装阀门，而流量是稳定的线性流动。
和柱塞泵相比，单螺杆泵具有更好的自吸能力，吸上高度可达8.5米水柱。
和隔膜泵相比，单螺杆泵可输送各种混合杂质，含有气体及固体颗粒或纤维的介质，也可输送各种腐蚀性物质。
和齿轮泵相比，单螺杆泵可输送高粘度的物质。
与柱塞泵、隔膜泵及齿轮泵不同的是，单螺杆泵可用于药剂填充和计量。
|
|
